John Lewis JLDWW1203 Bedienungsanleitung PDF herunterladen (Seite 14)

Setting the Water Softener

The water softener must be set manually and electronically:

a) Setting manually

The dishwasher must be switched off.

1. Open the dishwasher door.

2. Remove the lower basket from the dishwasher.

3. Turn the water hardness dial to position 0 or 1 (see table).

4. Replace the lower basket.

The dishwasher is factory set at position 0.

b) Setting electronically

3 The electronic setting of the water softener is

possible ONLY with the Multi-tab function de-

activated.

1. Press the On/Off button.The On/Off indicator light and all the

programme indicator lights will illuminate (setting mode).

If only one programme button indicator light is on, this means

that a washing programme is set.The programme must be can-

celled:

press simultaneously function buttons 1 and 2 for about 2 sec-

onds. All programme indicator lights will illuminate indicating

that the set programme has been cancelled and the machine is

now in setting mode.

2. Press function buttons 1 and 2 simultaneously and hold them

down.

The LED indicators for function buttons 1 to 3 will flash.

3. Press function button 1.

The LED indicator for function button 1 will flash.

The multi-display will indicate the hardness setting.

4. Pressing function button 1 increases the hardness setting by

(Exception: hardness setting 1 follows hardness setting 10).

Examples:

If the current level is 5, by pressing function button 1 once,

level 6 is selected.

If the current level is 10, by pressing function button 1 once,

level 1 is selected.

5. When the hardness setting is correct, press the ON/OFF

button.

The hardness setting is now saved.

If the water softener is set electronically to “1”, this switch-

es off the control indicator for dishwasher salt.

Filling with dishwasher salt

Only use salt specifically designed for use in dish-

washers.

All other types of salt not specifically designed for

use in a dishwasher, especially table salt, will dam-

age the water softener.

Only fill with salt just before starting one of the

complete washing programmes.

This will prevent any grains of salt or salty water,

which may have been spilt, remaining on the bot-

tom of the machine for any period of time, which

may cause corrosion.

To f i l l :

1.Open the door, remove the lower basket and unscrew

the cap of the salt container by turning it anticlockwise.

2.Pour 1 litre of water inside the container (this is neces-

sary only before filling with salt for the first time).

3.Place the funnel (supplied) over the dispenser opening.

Fill the dispenser with dishwasher salt; the capacity of the

dispenser is approx. 1.0-1.5 kg, depending on the size of

the grains. Do not overfill the dispenser.

4.Replace the cap making sure that there is no trace of salt

on the screw thread or on the gasket.

5.Replace the cap tightly turning it clockwise until it stops

with a click.

The salt container will require topping up periodically.You

are reminded of this by the salt indicator light on the con-

trol panel which comes on when the salt has finished.

The salt indicator light on the control panel can re-

main illuminated for 2-6 hours after the salt has

been replenished, assuming the dishwasher remains

switched on. If you are using salts that take longer to

dissolve then it will take longer. The function of the

machine is not affected.

Do not worry if water over flows from the unit when filling

with salt, this is quite normal.

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 31 32

Kommentare zu diesen Handbüchern

Keine Kommentare

John Lewis JLDWW1203 Bedienungsanleitung Seite 14

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Geschirrspüler John Lewis JLDWW1203